Hex Head Bolts, Hex Head Screws, Allen Head Bolts, Socket Head Bolts, Allen Grub Screws, Socket Set Screws, Studs Bolts, Studs, Counter Sunk Screws, Slotted Counter Sunk Screws, Lifting Eye Bolts
 
 

Foundation Bolts

Using IS:2062 Grade A, En-8, En-19 material as per IS-1367 Class 8.8 / Class 10.9 or as per the requirement of the customer.

Manufactured as per IS-5624, DIN 267, and DIN 529 with 2 nuts & washers Type A, B, C & D.
J Type / L Type Foundation Bolts with Class 8 nut, 1 washer and 1 lock nut.
Plate Type Foundation Bolts with 1 nut & 1 washer.
Chimney Foundation Bolts.
Long length (up to 6000 mm) Rock Bolts in Torr-Steel with 1 nut & 1 washer.
Rail Track Foundation Bolts with 1 nut, 1 washer, 1 spring washer.
Other Foundation Bolts as per specific requirement & drawing.
 
Studs Bolts / Studs
studs bolts

 

Using IS:2062 Grade A, En-8, En-19, SS-410, SS-304, SS-316 or any other material as per the specification of the customer. As per IS:1367 Class 5.6, Class 8.8, Class 10.9, Class12.9, ASTM A193 B7, ASTM A193 B8, B8M, B16, ASTM A563 L7, L7M.

Surface Treatment: Blackodised, Phosphated, Zinc Plated with yellow, blue, olive green passivation.

Threading sizes from M6 to M100 ISO Metric 6g as per IS:4218 or equivalent in BSW / UNC, of following types

Full Thread Studs as per DIN 975. Rods with Threading on one side as per DIN 524.
Studs with Threading on two sides as per DIN 939, DIN 940, IS 1862 Type A, B & C.
Tip-Welding Studs.
Tie Rod Studs for Plate Type Heat Exchangers.
Square / ACME Thread Studs (Lead Screws).
Other Studs as per your specific requirement and drawing.
 
Hex Head Bolts
ASTM A193, A194 A490M / ASTM A 325M Hardware
This specification covers the B7, B8, B8M grade & High Strength Steel Bolts Classes 10.9 and 10.9.3 for Structural Steel Joints. These are also called as High Friction Grip Bolts or Structural Bolts. Sizes range from M12 to M36.

Hex Head Bolts/Screws & Fit Bolts


Using IS:2062 Grade A, En-8, En-19, SS-410, SS-304, SS-316 or any other material as per customer specification. As per IS:1367 Class 5.6, Class 8.8, Class 10.9, ASTM A 193 B7, B8, B8M, A2-70, A4-70, A4-80 Dimensions of Hex Head Bolts/Screws as per IS:1364, ANSI B18.2.2, IS:3757/DIN:6914 or as per customers’s requirement. Dimensions of Hex Head Fit Bolt as per IS:3640/DIN:610 or as per customers’s requirement.

Surface Treatmeant : Blackodised, Phosphated, Zinc Plated with yellow, blue, olive green passivation.

Threading Sizes M6 to M100 ISO, Metric 6g, as per IS:4218 or equivalent in BSW / UNC of following types,

Full Thread Hex Screws.
Half Thread Hex Bolts.
Hex Bolts for Steel Structures as per IS:6639.
Special Hex Bolts as per DIN 561, DIN 933
Other Hex Bolts as per your specific requirement and drawing.
 
 
Allen Head / Socket Head Bolts

Using IS:2062 Grade A, En-8, En-19, SS-410, SS-304, SS-316 or any other material specified by customer. As per IS:1367 Class 5.6, Class 8.8, Class 10.9, ASTM A 193 B7, B8, B8M, A2-70, A4-70, A4-80.

Surface Treatmeant: Blackodised, Phosphated, Zinc Plated with yellow, blue, olive green passivation.

Threading Sizes M6 to M100 ISO, Metric 6g, as per IS-4218 or equivalent in BSW / UNC of following types,

Full / Half Thread Allen Bolts as per IS-2269/DIN:912/ISO:4762. DIN:6912, DIN:7984
Other Allen Bolts as per customer’s requirement

Socket Head Bolts

 
 
Allen Grub / Socket Set Screws

Using IS:2062 Grade A, En-8, En-19, SS-410, SS-304, SS-316 or any other material as per your specification. As per IS:1367 Class 4.6, Class 5.6, Class 8.8, Class 10.9, A2-70, A4-80.

Surface Treatment: Blackodised, Phosphated, Zinc Plated with yellow, blue, olive green passivation.

Threading Sizes M3 to M24 ISO, Metric 6g, as per IS-4218 or equivalent in BSW / UNC of following types,

Cup Point with Knurling as per IS : 6094.
Dog Point as per IS: 6094
Pointed as per IS: 2064.
Other Grub Screws as per customer’s specifications
.
 
 
Counter Sunk Screws (Slotted / Allen)

Using IS-2062 Grade A, En-8, En-19, SS-410, SS-304, SS-316 or any other material as per customer’s specification. As per Class 4.6, Class 5.6, Class 8.8, Class 10.9, A2-70, A4-70, A4-80.

Surface Treatment: Blackodised, Phosphated, Zinc Plated with yellow, blue, olive green passivation

Threading Sizes M6 to M24 ISO, Metric 6g, as per IS-4218 or equivalent in BSW / UNC of following types,

Dimensions as per ISO-898/1
 
 
Eye Bolts / Lifting Eye Bolts

Using IS:2062 Grade A, En-8, En-19, SS-410, SS-304, SS-316 or any other material as per customer’s specification. As per IS-1367 Class 4.6, Class 8.8, Class 10.9, A2-70, A4-70, A4-80

Surface Treatment: Blackodised, Phosphated, Zinc Plated with yellow, blue, olive green passivation.

Threading Sizes M6 to M30 ISO, Metric 6g, as per IS-4218 or equivalent in BSW / UNC of following types,

Manufacturing as per IS:4190 / DIN 580 and as per drawing.
 
 
U-Clamps
U-Clamps
Using IS:2062 Grade A, En-8, En-19, SS-410, SS-304, SS-316 or any other material as per customer’s specification. As per IS:1367 Class 4.6, Class 8.8, Class 10.9, A2-70, A4-70, A4-80

Surface Treatment: Blackodised, Phosphated, Zinc Plated with yellow, blue, olive green passivation.

Threading Sizes M6 to M24 ISO, Metric 6g, as per IS-4218 or equivalent in BSW / UNC of following types,

Suitable for 15NB (1/2”) upto 300 NB (12”) Pipes.
Suitable for 12.5 (1/2”) upto 300 (12”) OD Pipes.
Available in Rod Sizes 6mm to 20mm with 2 Nuts & 2 Washers.
Available in Flat (Patti) for above sizes.
Any other sizes as per customer’s drawing & requirement
 
 
Anchor Bolts
Using IS:2062 Grade A, material or in SS-304, SS-316 or any other material as per customer’s specification.

Surface Treatment: Zinc Plated with Yellow, Blue, Olive-Green passivation. Threading sizes from M6 to M30 with 1 Nut & 1 Washer.
J Clamps & L Clamps
Using IS:2062 Grade A, material or in SS-304, SS-316 or any other material as per customer’s specification. As per IS:1367 Class 4.6, Class 5.6, Class 8.8, Class 10.9, A2-70-, A4-70, A4-80.

Surface Treatment: Zinc Plated with Yellow, Blue, Olive-Green passivation.

Threading sizes from M6 to M 24 ISO Metric 6 g as per IS 4218 or equivalent in BSW / UNC of following types.

Suitable for Angle Fitment (J Clamp) of GJ / Asbestos Cement Corrugated and non-corrugated sheets. With 1 sq. nut, 1 MS Washer & 1 Tar Washer.
Suitable for pipe fitment (J Clamp) of GI / Asbestos Cement Corrugated and non-corrugated sheets. With 1 sq. nut, 1 MS Washer & 1 Tar Washer.
Suitable for channel fitment (L Clamp) of GI / Asbestos Cement Corrugated and non-corrugated sheets. With 1 sq. nut, 1 MS Washer & 1 Tar Washer.
Any other size as per customer’s requirement.
Nuts
Using IS:2062 Grade A, En-8, En-19, SS-410, SS-304, SS-316 or any other material as per customer’s requirement. As per IS:1367 Class 4, Class 8, Class 10, A2-70, A4-70, A4-80

Surface Treatment: Blackodised, Phosphated, Zinc Plated with yellow, blue, olive green passivation.

Threading Sizes M6 to M100 ISO, Metric 6g, as per IS-4218 or equivalent in BSW / UNC of following types,

Standard Nuts as per IS:1364/ ISO 4032. HSFG Nuts as per IS:6623/ ISO 4775/DIN:6915 (size    from M16 to M36) Standard & Heavy Hex Nuts as per    ANSI B18.2.2 standard.
Lock Nuts as per IS:1364.
Nylock Nuts.
Long / Double Nuts
Castle Nuts as per IS:2232
Round Nuts
Any other nut as per customer’s drawing & requirement
Washers
Washers
Using IS:2062 Grade A, En-8, En-19, SS-410, SS-304, SS-316 or any other material as per customer’s requirement.

Surface Treatment: Blackodised, Phosphated, Zinc Plated with yellow, blue, olive green passivation.

Threading Sizes M4 to M64 ISO, Metric 6g, as per IS-4218 or equivalent in BSW / UNC of following types,

As per IS:2016 Type A Punched Washers for Hex Bolts & Screws.
As per IS:2016 Type B Punched Washers for Round & Cheese Head Screws.
Any other Washers as per customer’s requirement.
Machined Components
We manufacture machined components, spare parts & special fasteners as per customer’s requirement. We also undertake Job Working on labour charges as per customer’s requirement.
Readymade Hardware
We are also stockiest and supply hardware of reputed brands such as LPS, TVS etc with proper surface treatment and ensure gauge fitment after surface treatment as per customer’s requirement & drawing.